| A16-59N2 Rotek Slewing Ring Bearings | Tolerance housing:H7; Specific dynamic load factor K:10 N/mm²; Specific static load factor K0:20 N/mm²; Permissible sliding velocity v min.:0.25 m/s; Coefficient of friction µ min.:0.05; D:80 mm; Mass bushing:0.44 kg; Permissible sliding velocity v max.:5 m/s; Tolerance shaft:h8; d:70 mm; B:60 mm; Coefficient of friction µ max.:0.1; |
| 232.20.0400.503 Type 21/520.2 Standard 5 Slewing Ring Bearings | D1 ≈:50.8 mm; B:16 mm; Calculation factor Y1:0.66; b:4.5 mm; d:30 mm; D:62 mm; Fatigue load limit Pu:1.29 kN; Calculation factor Y2:1.07; da min.:35.6 mm; Calculation factor A:0.00256; Calculation factor X:0.6; Mass bearing:0.24 kg; r0:0.5 mm; ra max.:1 mm; Basic dynamic load rating C:37.5 kN; a:32 mm; Limiting speed:19000 r/min; r1,2 min.:1 mm; d1 ≈:37.5 mm; h:3.5 mm; |
| M5-26P1 Rotek Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:143000 N; Grease Speed Rating Open/Shielded n1:3800 rpm; d:70.000 mm; Sealed Speed Rating n3:2600 rpm; B:42.00 mm; Oil Speed Rating Open/Shielded n2:4500 rpm; Basic Static Radial Load Rating Co:104000 N; Accessories:Two Shields; Fillet Radius ra:2.50 mm; D:180.0000 mm; |
| 3R13-128N1A Rotek Slewing Ring Bearings | Pa:190 kN; P0°:450 kN; Q180°:200 kN; Cap bolt, size:M 16x90; H1:112 mm; A2:166 mm; H2:35 mm; Oil seal:2 x TSN 519 U; P150°:230 kN; N1:22 mm; Mass housing:13.7 kg; Q120°:400 kN; Oil level, min.:38 mm; Da:170 mm; P55°:580 kN; Locating ring:2 x FRB 12,5/170; P90°:350 kN; da:85 mm; Cap bolt, rec. tightening torque:150 N·m; N:28 mm; |
| M5-40P1 Rotek Slewing Ring Bearings | B:7 mm; D:68 mm; D1:37 mm; Mass housing washer:0.14 kg; r1,2 min.:1 mm; |
| 3R8-88N9 Rotek Slewing Ring Bearings | Tolerance housing:H7; Coefficient of friction µ min.:0.05; D:95 mm; Tolerance shaft:h8; Coefficient of friction µ max.:0.1; B:80 mm; Specific static load factor K0:20 N/mm²; Mass bushing:1.04 kg; d:80 mm; Permissible sliding velocity v min.:0.25 m/s; Permissible sliding velocity v max.:5 m/s; Specific dynamic load factor K:10 N/mm²; |
| 231.20.0400.013 Type 21/520.1 Standard 5 Slewing Ring Bearings | G:M 110x2; B2 ≈:63 mm; Reference speed:3400 r/min; d1:95 mm; d2 ≈:118 mm; D:215 mm; Calculation factor Y1:2.8; Calculation factor Y0:2.8; da min.:108 mm; B1:59 mm; D1 ≈:159 mm; Basic dynamic load rating C:433 kN; G1:10 mm; K:4.5 mm; Mass bearing + sleeve:9.1 kg; B:47 mm; r1,2 min.:3 mm; Fatigue load limit Pu:49 kN; Calculation factor Y2:4.2; Calculation factor e:0.24; |
| 3R10-98N1B Rotek Slewing Ring Bearings | Recommended diameter for attachment bolts, inch G:0.625 in; Thread grub screw G2:3/8-24 UNF; Mass bearing unit:2.65 kg; A:54 mm; Fatigue load limit Pu:0.98 kN; N:26 mm; J min.:149 mm; Limiting speed:800 r/min; N4:4 mm; s1:32.6 mm; A1:34 mm; H:114 mm; H2:22 mm; A5:29.5 mm; N1:18 mm; Basic dynamic load rating C:35.1 kN; B:51.6 mm; d:49.213 mm; L:203 mm; H1:57.2 mm; |
| W13-43P2 Rotek Slewing Ring Bearings | A2:379.425 mm; Housing:SSAFS 056 KAUA; Mass pillow block:392 kg; H2:101.6 mm; ba:100.806 mm; H1:250.825 mm; P120°:249 kN; RG:1 NPT; Stabilizing ring:2 x A8819; P90°:400 kN; A1:228.6 mm; Initial grease fill:3515.4 g; P60°:669 kN; Pa:89 kN; h:73.025 mm; Cap bolt, SAE grade:8; Ca:147.803 mm; H:495.3 mm; R2:50.8 mm; R1:163.512 mm; |
| 161.16.0400.891.21.1503 Standard 5 Slewing Ring Bearings | Basic Static Radial Load Rating Co:6800 N; Basic Dynamic Radial Load Rating C:11700 N; Grease Speed Rating n1:14000 rpm; d:12.000 mm; Accessories:One Shield; Oil Speed Rating n2:18000 rpm; B:19.1 mm; D:37.0000 mm; Fillet Radius ra:1.00 mm; Sealed Speed Rating n3:14000 rpm; |